Відео

Thank you so much for the Nissan part number! Im doing this exact set up and have been searching all day for a receiver for my 04 s2k!

Super helpful I did this with tools camping I knew what I needed based on this video what a difference the downpipe makes , thanks for the laughs

Hey do you have a part number? Or where did you purchase the slave cylinder. I need to do the same to my 1986 944. Thanks

3100 not 3800

bro that the worst explanation ive ever seen on a DS1 smfh

I'm assuming your car did not have Dynamic chassis control? My 2015 GTI with DCC had the ability to hold sustained speeds of 180km/h and almost 1.5 Gs on our race track. That was with Michilen PS4S tires. My new 2024 GTI with no DCC is definitely trying to kill me in high speed corners because of a lack of stability. I'll probably go the same route...better tires first and a rear sway bar with adjustable end links....Or trade the damn thing in for a car WITH DCC.

Doing this in the driveway right now with no ramps, not bad just tedious with an allen key. The one they gave with the product is softer than butter so i recommend having your own.

You had to move your jackstand because it was in the wrong place to begin with. The rear jack point is after of the rear wheels. Considering the what I’ve seen up to that point this is a terrible video if you are trying to show your mechanical acumen.

Where you experiencing bump steer on track?

Did you have any lights blinking or not turning on in the ac panel?

Well it’s food for thought. I have already got a wheel hub. I mean this would explain how it’s on and off. Especially that a day ago I noticed just bouncing in my seat would cause the messages to pop up. I just don’t like how I’ve noticed sometimes when I make a turn or something similar the traction control will activate when I know it doesn’t need to. The only thing my impala did for its entire life was drive across Texas as a fleet car. 😅 I got a rust free car in Nebraska.

just got my transmission down and cracked open today after like 6 days of work. so far the hardest part was the top bolts connecting the downpipe to the turbo which took like 7 hours to remove 😅

4:38 I think that's the evap leak test cycle that happens a couple hours after shutoff. EPA thing

I appreciate you tons for this video! It definitely helped me out so much and the advice to get a transmission jack is what made this so easy to do on my own! Thank you. Although, my transmission seemed like it was super glued and I didn't have the courage to pry on aluminum casts so I used MAP gas to heat around the pass side dowel for about 3-5 minutes. Took me around 20 minutes to get the transmission on the ground including the heat time.

Holy cow, back in the day all you had to do is unscrew the light..... smh

Good job on the video, I wonder if it isn't a Honda common issue. My steering shakes while hard breaking and or going down hill. I suspect it is the tie rod end. I will start with it and see how it goes. Suspension seams tight otherwise.

Did it help at the track?

You've got to be two of the stupidest people in history. You have gas all over the place, which means gas fumes all over the place, and you are clanking metal on metal carelessly, which could cause a spark and the end of both of you, and your MX5. Lol. WOW!!!!

Nice car! I also have a white VB with the same spec and color rpf1 lmao. Probably getting these springs here soon as well. Can’t decided between coils or springs.

Hello, I know this is late, but I followed your procedure and when I went to turn on my car, the car threw a lot of dash lights and the battery wouldn’t turn on. Any suggestions on why this happened?

Will remote start work if you leave the car in gear? Or do you have to leave it in neutral with the brake up?

I think Dan kinda looks like the Water Jet Channel guy.

Thanks for this video it helped me out a lot.

I thought the cooler line was the low pressure, cuz thats where the fluid cools down?

Thanks for this video

Thanks! I was needing the adapter bracket for the rears, along with the harness adapters! No local shops could find any and even Crutchfield didn't show an application for the rears.

Just what I needed to know. Well actually more than…. I hope I can avoid the extra work!

Awesome ty for the info

Excelente video !

Good video

Our 3023 C8 HTC can lower the top in about 16 seconds while traveling up to 30 mph. Apples to apples. It also goes from 0-60 in 3 seconds or less and the 1/4 mile in the low 11s. It is also roomier inside and very comfortable to drive.

Would the belts in the description work for my 1992 na Miata with a/c and P/s? Thanks!

Is there another video that shows the whole repair?

Dude, You're one of the only videos I've seen about installing a remote start on a VB WRX. Its seems so straight forward, that I want to try it myself. I've been quoted anywhere from $1,200, to the lowest $750 to have a remote start installed on my 2023 base. That's The other thing, that worries me, you made it seem pretty easy to figure out, although mine is a base model so I don't have the push to start, key only. but I imagine it should work the same way? So tempting, because this is a much cheaper alternative to paying somebody almost $800.

Does this work for brake pedals as well?

Could you put the new fittings in with the clip already on, this way all you have to do is push the hose in until it clicks.

Did you have to drain the transmission oil

hi I installed my new b14s with new bilstein front bearings on my s3 8v. Is it normal to have a slight noise on the bearings when steering from a standstill? they told me it depends on the lowering springs. Front -22 and rear -20. thanks bye

Thank you so much for making this video! You made it so easy for me to fix my droopy eye air vents. I ended up using soft velcro with a sticky back & they work like a charm.

Now let it sing.😂

Very helpful - thanks for taking the time to post this - I am currently in the process of the water pump replacement

was it the pcv that was bad?

Do you think this kit would be friendly for a base model ? ( without the push to start button ) .. thx !!

Hello I checked everywhere no leak but only at the shaft so I’m thinking it’s the pressure line so would it be ok just to change the O ring?

Annoying 😣

Get a pro tune to have piece of mind

Once its been replaced, do i need to reprogram the thermostat?

sounds like a ferrari v8 idling

Do you need a tune for this?

Could you have just done this job on the ramps?